It is run by a group of enthusiastic Kaleidescape owners and dealers purely as a service to this community. This board is not affiliated in any way with Kaleidescape, Inc. For official technical support, product information, or customer service, please visit www. The forum is free to use and most of the forum can be used by guests who are not registered There is no cost to register for a full account. Benefits of registering for a full account: Participate in the discussions!
|Published (Last):||2 December 2017|
|PDF File Size:||6.2 Mb|
|ePub File Size:||13.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
Exposing the Rollers 1. Remove the front panel by gripping each side and pulling it straight from the disc vault. See Figure 1. Figure 1 Removing the Front Panel 2. Remove the disc vault from the rack. Use a Phillips screwdriver to unmount the ears from the rack. A two-person lift technique is required to safely remove a disc vault from the rack. Take off the rack ears, using a 2. See Figure 2.
Remove 6 screws from the back, using the 2. See Figure 3. Cut the warranty sticker with a box knife. Remove 7 screws from the longer side. Do not remove the screw marked in red. See Figure 4. Remove 6 screws from the shorter side. See Figure 5. Take off casing by sliding it back towards the rear of the vault. Then lift it off.
See Figure 6 and Figure 7. Remove the 4 screws that hold the disc retention funnel to the roller brackets at the edges, using 2 mm hex screwdriver.
Remove the center screw, using a 4 mm hex screwdriver. Then lift the disc retention funnel off the base of the carousel. See Figure 8. If the discs were not able to be ejected, remove enough discs to expose the front and rear rollers. Fifty slots, centered at the rollers, should provide enough space to properly clean the rollers. See Figure 9. Note: Only one section, fifty slots wide, needs to be cleared.
Once one set of rollers is cleaned, the carousel can be rotated to clean the second set of rollers. Cleaning the Rollers The rollers should now be easily accessible and no discs should be close enough to the rollers to possibly become damaged during the cleaning process. Proceed with cleaning the rollers. Gently scrub the rollers, rotating them after one side has been cleaned. Rotate the rollers by holding the frame and moving across the rollers with your thumb.
See Figure 10 and Figure Note: One of the rollers will be easier to rotate then the other. If enough force is applied, the second roller will rotate. Rotating the carousel might be required if the discs were not able to be ejected. Proceed with putting the disc vault back together. Place the disc retention funnel back on top of the carousel and secure it with 4 screws that hold it to the roller brackets at the edges, then one in the center.
Replace the casing. Then slide the casing forwards into place. Check that the screw holes line up. Loosely replace 6 screws on the back. Replace 7 screws on the longer side and 6 screws on the shorter side.
Tighten all the replaced screws. Replace the front panel by lining up the metal tab at the bottom inside of the panel with the slot in the front of the chassis. Press firmly and evenly to snap the panel into place.
Install the disc vault back into the rack. Use a Phillips screwdriver to mount the ears to the rack. A two-person lift technique is required to safely install a disc vault into a rack. If discs were manually removed, the disc vault must go through a re-inventory process before the removed discs can be loaded into the disc vault again.
If discs were successfully ejected before the start of the procedure, after the disc vault has booted up, the discs can be loaded into the disc vault immediately.
Kaleidescape DV700 Disc Vault (Silver)
Exposing the Rollers 1. Remove the front panel by gripping each side and pulling it straight from the disc vault. See Figure 1. Figure 1 Removing the Front Panel 2.
Kaleidescape M700 Disc Vault
It is run by a group of enthusiastic Kaleidescape owners and dealers purely as a service to this community. This board is not affiliated in any way with Kaleidescape, Inc. For official technical support, product information, or customer service, please visit www. The forum is free to use and most of the forum can be used by guests who are not registered There is no cost to register for a full account. Benefits of registering for a full account: Participate in the discussions! You must have a registered account to make posts on the forums.
M700 Rack Mounting
In fact, you might be surprised that Kaleidescape has been in business since when it pioneered an entirely new entertainment category called the movie server. Like a larger, more powerful iPod with massive storage, Kaleidescape did for movie collections — importing, storing, managing — what other systems were doing with music. Over the past 12 years, the company has continued developing and refining its system, adding features and performance enhancements to stay atop the premium, luxury category it established. Since then, performance has improved, storage has increased, features have been added and the cost has been more than cut in half. However, 5-digits are still too much for most people to handle when contemplating a Blu-ray player, regardless of how many bells and whistles it includes. Out of the Box Typically, Kaleidescape systems are sold through its premium dealer channel and require professional installation. In reality, the system installs quite easily and, assuming no networking hijinks, is often up and in running in minutes.